Painted playing pieces

@SEP try this one he has just started doing 3d printed. http://iwillnevergrowup.com/shop/index.php?route=product%2Fcategory&path=62_93

I have been playing around with different configurations for a custom table and wanted to note some things I’ve landed on that I really like. A main one thing is having the map mounted so that it can slide around as needed on top of a bigger playing area. My table is 65” x 95” in total with a 5.5” arm rest around the outside and the middle is a recessed neoprene surface. I have the OOB Global map mounted on 1/2” rigid foam with a 1/2” aluminum frame around it. This allows the map to slide up close to whoever’s turn it is, but then be in the middle so both players can roll dice In front of them without disturbing the map and in easy view of the other player. (Plus we like lots of room to roll the bones). This ability to adjust the surface along with a standing height, makes it comfortable for long uses because you can move around more and don’t feel as tied down.
Things I’ve learned and changed from original design - I originally used too big of a frame for the map and mounted it on too high of a foam block (you can see these pictures at the bottom) - it made it hard to see the other player’s dice and the big frame took up too much real estate. My global map is mounted on much thinner foam (the framing is bad, you can see if you look closely) but I also used much thinner aluminum angle for the frame. This gives just enough grip when needing to move the map around (I use furniture slides on the bottom, which glide very nicely on the neoprene) but doesn’t make the whole thing too bulky. Having it an inch or so off the surface keeps the dice off, but isn’t so heigh that you can’t see the other player’s dice rolls. When playing other versions (such as Zombies) the board is much smaller, but it can easily swap in and out on the same table since it can move around where ever it is needed or be pushed aside.
I originally made it normal table height, but found long reaches while sitting were harder and it just felt cramped. Standing height with a bar stool is a great way to have the best of both worlds.
The 5.5” rim around the table itself gives you a nice arm rest that doesn’t interfere with the gaming surface. I’m playing with how to best add some cushion to this part - open to suggestions. Sometimes I just lay a piece of leftover neoprene on it.
Dice bounce nice on the neoprene and stay off the floor. It also feels nice and has enough give to allow things to slide but be picked up easily. Wouldn’t definitely go with neoprene again as a surface covering.
I made the drawers open to the inside of the table so you can stay hunched over the action while accessing and stowing stuff away. 50/50 on whether I would keep this if I were to do it again. If I were doing it again, I might try to build customer drawers form scratch using actual drawer glides, but that was beyond my ability when I first did this, so I just used clear plexiglass boxes with aluminum pulls mounted on them. It’s nice having them clear, and I was happy with how the pulls came out, but without glides they can be a little fussy sliding in and out of their slots.
I originally designed the table so that I could put a cover surface back on top when not in use, but find I don’t really ever do that, so if I were to do it again, I might not mess with that part (I never even finished staining those as you can see in the pictures).
CF362D52-269F-4480-8CBB-08139099138F.jpeg A9E12EA1-66EB-4671-86AC-68C62FD30AD5.jpeg 858DE1F2-030A-4D5A-93E4-70A7D1180ADB.jpeg 8F513EE0-DA37-4BA9-880E-4D5EF7BF431F.jpeg F0188165-757B-4CC1-BF67-5045832283C9.jpeg 2E3CD627-0D31-4121-ACF8-682F9F58A40B.jpeg

https://www.facebook.com/pg/Landing-Vehicle-Tracked-LVT4-2017381051873202/photos/?tab=album&album_id=2201403350137637

I have seen lots of people here use acrylics and I have on occasion. Most of my paints are enamels though. I find that is stays wet longer (which is a good thing) and doesn’t clump up nearly as much on your brush. I also use enamels in my airbrush. I find that enamels are actually much easier to clean than acrylics. While acrylics are water soluble, they don’t just dissolve, especially if already dry. It involves a great deal of scrubbing and scraping. With enamels, all you need is some mineral spirits cleaner and it takes the paint right off with very little effort. Cleaning acrylic paint out of my airbrush was hell the first time I did it… never using acrylics in there again. In terms of the finish, I can only assume that enamels hold up better to bumps and scrapes than acrylic paint does.

Someone once asked if enamels, by default, have a glossy finish to them. They do not, as long as you are using flat enamels, which seem to be the standard. I use flats and they have an excellent, non-shiny finish. I feel like enamel colors are a little deeper too, on the whole, but I suppose it depends on the brand of acrylic you use. Vallejo seems to be a popular choice for acrylics. I use predominantly Model Masters (Testors) enamels. In general, I would just said to find a brand you like to work with and produces the results you like. Don’t buy super cheap paint… you will get the results you pay for.

Good luck!

Dedo… sounds awesome, you’re a legend.  :-D

“YG”,

@Young:

AWESOME!

––I totally agree with your opinion of “Allworkandnoclay’s” painting talent.
----I’m sure you’d enjoy “SgtWilTan’s” thread about detailing units as well as “LHoffman’s” thread about painting them. They’re both really talented guys!
––In order for you to see all of the new units when they’re completed you might also want to stay tuned to my main thread because Sgt. Wil Tan has already detailed many new units that Lucas Hoffman will have painted before much longer. And I’m glad you enjoyed the “hoard”.

“Tall Paul”

@elrojo33:

That would be my answer. Anyway, I’ll keep an eye out. If I come across some I will let you know.
Happy hunting.

Thanks much.

Thank you Paul. These all look very cool. Looks like I have a few options.

Jon