Dangermouse finally found some time to paint…..

Thanks, Guys! I will try these Ideas out.

@cavestone I also use vallejo paints. The key question here is are you brush painting, or using an airbrush, or both?

The Vallejo paints have a “Model Air” line that comes pre-thinned. You can buy a thinning product (from them) to add to the “Model Color” series paints, which are the exact same thing, just more concentrated and thicker.

If you’ve never used an airbrush, its a bit finicky–it requires regular cleaning and a without a good brush and compressor the paint will flow very inconsistently. The process will be very frustrating unless you use the pre-thinned paints because the brush can only blow paint that is within a certain set of thickness parameters that are difficult to achieve, especially if you are trying to mix the air in the brush’s reserve or in small quantities. That’s why having copies of both Model Air and Model Color is fine by me–unlike Warhammer 40K I’m using primarily earthy colors, greens, dunkelgelb and dunkelgrau… other AFV and camoflage colors and so i don’t need a collection of primary or bright colors.

But I recommend it. The airbrush creates a sublime, beautiful layer and slight mix variations can be used to create shadows, grades, etc. Then you go back over with your brush, adding highlights, lines, details. Then, back over again with a drybrushing…then back to the airbrush to blast Flory Wash all over it.

Can’t see your photos, you can’t post photos until you have a certain post count. I wouldn’t use water to thin paints, they are water soluble but the mix and viscosity is all wrong (though water is obv. cheap and easy to clean up)

As for oil-based paints, these require thinner to clean up, they are much more difficult to drybrush with and are not used for airbrushing. The days of the old testors paints is long behind us–even apple barrel paints are easier to work with and cheaper. The early painting methods were much more about glomming thick layers of paint onto lead miniatures and the modern approach with water based paint and a series of different techniques creates much better results.

I have seen lots of people here use acrylics and I have on occasion. Most of my paints are enamels though. I find that is stays wet longer (which is a good thing) and doesn’t clump up nearly as much on your brush. I also use enamels in my airbrush. I find that enamels are actually much easier to clean than acrylics. While acrylics are water soluble, they don’t just dissolve, especially if already dry. It involves a great deal of scrubbing and scraping. With enamels, all you need is some mineral spirits cleaner and it takes the paint right off with very little effort. Cleaning acrylic paint out of my airbrush was hell the first time I did it… never using acrylics in there again. In terms of the finish, I can only assume that enamels hold up better to bumps and scrapes than acrylic paint does.

Someone once asked if enamels, by default, have a glossy finish to them. They do not, as long as you are using flat enamels, which seem to be the standard. I use flats and they have an excellent, non-shiny finish. I feel like enamel colors are a little deeper too, on the whole, but I suppose it depends on the brand of acrylic you use. Vallejo seems to be a popular choice for acrylics. I use predominantly Model Masters (Testors) enamels. In general, I would just said to find a brand you like to work with and produces the results you like. Don’t buy super cheap paint… you will get the results you pay for.

Good luck!

Very nice work. I’m way too unsteady of hand and mind to pull that off.

So very true. When I first started painting my aircraft I had to include decal roundels for the players to distinguish the pieces from one another. My naval units are painted mostly with a color scheme for playability except for the capital ships like the Carriers and popular Battleships. All of them have a decal or flag to show which nation they belong too. I actually replaced the OOB British Cruisers because I thought they looked too close in size with the destroyers. I ended up replacing with some ships I found on Shapeways. The biggest problem I had with naval units is that they can exist in the same seazone with enemy pieces unlike land territories. Because of this I decided to keep the subs, destroyers, cruisers and non unique battleships following a color scheme. There are so many colors in the spectrum though we should be able to come up with a solution that will make them look more historical yet keep the pattern or color scheme for the nation. I really would love to paint all the ships historically and maybe I will revisit them again someday. Every time I go back and repaint my pieces I seem to get better at it. Or at least I think I do, hehe.

The next group of infantry, will be, DESERT LIGHT INFANTYRY.

Until next time.

Cheers!

John

@elrojo33:

That would be my answer. Anyway, I’ll keep an eye out. If I come across some I will let you know.
Happy hunting.

Thanks much.

Guys,

@coachofmany:

very nice!
**––I’m glad you enjoyed them. Lord knows I CERTAINLY ENJOY HBG’S PRODUCTS!

Tall Paul**