Painted playing pieces

I am working on painting my 1914 game pieces and would love to see what you all have done. Especially naval, artillery and plane units. Thanks!

I have been playing around with different configurations for a custom table and wanted to note some things I’ve landed on that I really like. A main one thing is having the map mounted so that it can slide around as needed on top of a bigger playing area. My table is 65” x 95” in total with a 5.5” arm rest around the outside and the middle is a recessed neoprene surface. I have the OOB Global map mounted on 1/2” rigid foam with a 1/2” aluminum frame around it. This allows the map to slide up close to whoever’s turn it is, but then be in the middle so both players can roll dice In front of them without disturbing the map and in easy view of the other player. (Plus we like lots of room to roll the bones). This ability to adjust the surface along with a standing height, makes it comfortable for long uses because you can move around more and don’t feel as tied down.
Things I’ve learned and changed from original design - I originally used too big of a frame for the map and mounted it on too high of a foam block (you can see these pictures at the bottom) - it made it hard to see the other player’s dice and the big frame took up too much real estate. My global map is mounted on much thinner foam (the framing is bad, you can see if you look closely) but I also used much thinner aluminum angle for the frame. This gives just enough grip when needing to move the map around (I use furniture slides on the bottom, which glide very nicely on the neoprene) but doesn’t make the whole thing too bulky. Having it an inch or so off the surface keeps the dice off, but isn’t so heigh that you can’t see the other player’s dice rolls. When playing other versions (such as Zombies) the board is much smaller, but it can easily swap in and out on the same table since it can move around where ever it is needed or be pushed aside.
I originally made it normal table height, but found long reaches while sitting were harder and it just felt cramped. Standing height with a bar stool is a great way to have the best of both worlds.
The 5.5” rim around the table itself gives you a nice arm rest that doesn’t interfere with the gaming surface. I’m playing with how to best add some cushion to this part - open to suggestions. Sometimes I just lay a piece of leftover neoprene on it.
Dice bounce nice on the neoprene and stay off the floor. It also feels nice and has enough give to allow things to slide but be picked up easily. Wouldn’t definitely go with neoprene again as a surface covering.
I made the drawers open to the inside of the table so you can stay hunched over the action while accessing and stowing stuff away. 50/50 on whether I would keep this if I were to do it again. If I were doing it again, I might try to build customer drawers form scratch using actual drawer glides, but that was beyond my ability when I first did this, so I just used clear plexiglass boxes with aluminum pulls mounted on them. It’s nice having them clear, and I was happy with how the pulls came out, but without glides they can be a little fussy sliding in and out of their slots.
I originally designed the table so that I could put a cover surface back on top when not in use, but find I don’t really ever do that, so if I were to do it again, I might not mess with that part (I never even finished staining those as you can see in the pictures).
CF362D52-269F-4480-8CBB-08139099138F.jpeg A9E12EA1-66EB-4671-86AC-68C62FD30AD5.jpeg 858DE1F2-030A-4D5A-93E4-70A7D1180ADB.jpeg 8F513EE0-DA37-4BA9-880E-4D5EF7BF431F.jpeg F0188165-757B-4CC1-BF67-5045832283C9.jpeg 2E3CD627-0D31-4121-ACF8-682F9F58A40B.jpeg

E6000 will glue anything.

If you are really looking for a good finish on all your HBG pieces, you could buy a couple small cans of differing lacquers and test each one. $20 should get almost 3 cans worth. It may be a waste to some degree, but at least you can know for sure which one works best.

I have a flat Testors lacquer/sealant spray that I used on Tall Paul’s finished pieces. Granted, these were painted first, so the effect may be thrown off. However, I will say that I did not observe any level of gloss on the HBG or OOB pieces after I applied it. It was quite flat as advertised. FWIW.

@dangermouse650:

@John:

@dangermouse650:

Great work John

Thanks DM.

Where have you been?

Have you been working, as of late?

Yes, work has been very hectic and other life happenings that are keeping me too busy to paint……but keep up with yours your doing great. :-)

Appreciate it DM. I hope you get to paint soon. :-)

John

I keep my games separate, however I add pieces to them from HBG.

@robbie358:

Hello all.  I thought I would solicit your thoughts on which types of pieces in any version of A&A scream for painting the most.

IMHO, the most confusing piece on the board in the original Pacific and Pacific 1940 is the USA fighter in China.  Having to differentiate between a Chinese fighter that looks American and any USA fighters in that zone seems like a headache waiting to happen.

Otherwise, I would say the pro-Axis and pro-Allies neutrals in Europe 1940 need attention.  The fact is that upon being attacked, you’re supposed to pick any random country to donate an infantry to that territory.  If the attacker doesn’t win, the infantry stay there but cannot be moved.  Seems like confusion might set in eventually.

Your thoughts?

HBG has British infantry for sale. I bought 25 and painted them white to use for neutral armies.

@sgtwiltan:

Yes. There are so many. Trying to get one thing done at a time. I sent back some pieces and have started on a big batch of artillery which he loves. I’m amazed at his patience. Still have a lot of pieces he sent me and was able to find and keep them in a box so I know which pieces are his that I need to work on. They had been lost in multiple boxes from when I moved 4 years ago. I’ve also redone literally hundreds of PZIIIs including some all of the painted ones. One of these days…… I’ll get them done.

That is cool! I’m sure he doesn’t mind, because the end result is fantastic. :-)